→ 상품 상세 정보 : VMM-D3 Shutter Driver
Overview
This product is not available for sale to the European Union. Please contact us for questions.
The Uniblitz VMM-D3 is a three-channel shutter driver capable of independently controlling up to three shutters. This compact design puts three complete, individual shutter drivers in a single, streamlined package. Active high-level logic inputs allow fully independent shutter control. A single input will activate all channels simultaneously, and a single output is available to monitor when all shutter synchronization system circuits are active. Three active low-level logic outputs monitor the status of each synchronization system output. An addressable RS232-C serial input is also available to control these inputs via a computer serial port, allowing up to eight VMM-D3 units and up to 24 individual shutters to be controlled from a single computer serial port.
See the VMM-D3 User Manual for additional information regarding this device.
The VMM-D3 is RoHS compliant.
What’s Included
- VMM-D3 Shutter Driver
- Manual (included on flash drive)
- 710C Interconnect Cables (3) (3.0 m)
- Line Cords (USA and Euro)
- Fuses (2) (0.25 AMP S-B)
Shutter Compatibility
| CS | DSS | LS | NS | TS | VS | XRS |
|---|---|---|---|---|---|---|
| CS25 | LS2 | VS14 | XRS6 | |||
| CS35 | LS3 | VS25 | XRS14 | |||
| CS45 | LS6 | VS35 | XRS251 | |||
| CS65 | ||||||
| CS90 |
1 Will require two drive channels for operation
Don’t see your device listed above? Please contact us for information regarding the compatibility of other shutter devices.
Specifications
| System Characteristics | |
|---|---|
| Repeat Exposure | Min 50 msec between exposure for 25mm or smaller aperture shutters |
| Min 120 msec for 35mm and larger aperture shutters | |
| Shutter Drive | Continuously variable frequency of exposures from DC to the shutter in operation |
| Maximum rate detated by 75% when more than one channel in operation | |
| All Inputs | Input Impedance – 4.7K Ohms |
| Input Control | Active-High |
| Terminal Block | TTL Compatible |
| All Outputs | Source Impedance – 1K |
| Output Control | Active-Low |
| Terminal Block | TTL Compatible |
| General | Size (HWD) 2.63 x 5.35 x 8.18 inches (67.0 x 136.0 x 207.9 mm) |
| Weight 4.5 lbs (2.02kg) | |
| Power 115/230 VAC, 50-60 Hz | |
Front Panel Layout
Simple and straightforward controls allow the VMM-D3 to be easy to use and configure. LED indicators reveal each shutter’s status at a glance. Three fuse holders with .6A slow blow fuses, accessible at the front panel for ease or replacement. N.O./N.C. switches allow manual shutter operation. Addressable RS-232C control is available via the DB-9 connector. Address selected by SW1.
| Front Panel | |
|---|---|
| Shutter Fuse (1) | 5 x 20mm,0.6A, “T” time-lag fuse to protect that shutter output-one for each channel. |
| N.O/N.C Switch (2) | The position of the key switch determines shutter status BEFORE a trigger signal is received by the VMM-D3-one for each channel. |
| Sync. Active LED(3) | A green LED indicator that indicates status of Solid State Synchronization output-one for each channel. |
| Driver Active LED (4) | A red LED that indicates when the internal shutter driver circuit input has an active signal present- one for each channel. |
| RS-232C Input (5) | DB-9 female connector provides access to the VMM-D3 RS-232C interface. |
| Address Select Switch-SW1 (6) | Selects the active RS-232C address of the unit. |
| Power Indicator (7) | A red LED indicates that power is applied to the unit. |
Rear Panel Layout
All main input/output functions can be accessed at the VMM-D3 rear panel, including the 115/230VAC input. Manual switching as required. Additionally, (2) 6-pin pluggable terminal strips allow for easy termination to input (active high) and output (active low) signals. Channel #4 output is not operational.
