---
title: "D880C Shutter Driver"
url: "https://bmlaser.co.kr/d880c-shutter-driver/"
description: "문의하기##OverviewTheUniblitzD880Cisanopen-frame, uni-stableshutterdriverutilizingconstantcurrentcontrolwhichhasshowntoincreaseshutterlifetimeoverstandardcapacitivedischargetypes."
image: "https://bmlaser.co.kr/wp-content/uploads/2018/07/bmlaser-logo2.png"
type: "Article"
datePublished: "2021-04-13T14:37:28+00:00"
dateModified: "2021-04-16T01:10:09+00:00"
---

# D880C Shutter Driver

## 핵심 요지

이 글은 D880C Shutter Driver에 대해 설명합니다. See the D880C User Manual for additional information regarding this device The D880C is RoHS compliant

# D880C Shutter Driver

[문의하기](https://bmlaser.co.kr/contact-us-2/)##OverviewTheUniblitzD880Cisanopen-frame,uni-stableshutterdriverutilizingconstantcurrentcontrolwhichhasshowntoincreaseshutterlifetimeoverstandardcapacitivedischargetypes.Itiswell-suitedforintegrationintoOEMapplicationswhenpairedwithalargeselectionofUniblitzshutters(allcompatibleshutterdeviceswillrequirethe“E” option (“For use with VED24 or D880C”) in order to properly operate with the D880C).

Simple external connections to the D880C are made through the pluggable input/output screw terminal connector. This enables the D880C to be quickly connected/disconnected without having to remove any wires connected to the terminal block. Control of the D880C requires that the user supplies a TTL (5V) logic level to the trigger input or connecting a mechanical or electronic switch between the trigger input and +6.

75 VDC. See the [D880C User Manual](https://www.uniblitz.com/wp-content/uploads/2017/01/D880C-User-Manual-2.00_Rev_C.pdf)foradditionalinformationregardingthisdevice.TheD880CisRoHScompliant.##What’s Included - D880C Shutter Driver - Manual (included on flash drive) - 710P Shutter Interconnect Cable A power supply is not included with this device.

### Shutter Compatibility | VS | LS | CS | DSS | TS | NS | XRS | |---|---|---|---|---|---|---| | VS14 1 | LS2 1 | CS25 1 | | | | XRS6 1 | | VS25 1 | LS3 1 | CS35 1 | | | | XRS14 1 | | VS35 1 | LS6 1 | CS45 1 | | | | XRS25 1, 2 | | | | CS65 1 | | | | | Will require “E” option (“For use with VED24 or D880C”) for D880C compatibility. Will require two drivers for operation. Don’t see your device listed above?

Please [contact us](https://www.uniblitz.com/contact-us/)forinformationregardingthecompatibilityofothershutterdevices.##Specifications| System Characteristics | |---| | Repeat Exposure | Minimum time between exposures is determined by shutter used and open close pulse duration. | | Shutter Drive | Continuously variable frequency of exposures from DC to the shutter in operation maximum rate. | | | Pulse Current: 1.

2A | | | Hold Current: 300mA | | General | Size (HWD) 1. 00 x 3. 20 x 4. 00 inches (25. 4 x 81. 2 x 101. 0 mm) | | | Weight 3. 00 oz (0. 09 Kg) | | | Power input: +24VDC at 1. 5A (user supplied) | | | RoHS Compliant |

## Board Mechanical Layout | P1 Connections | |---| | Pin 1 | Input | +24 VDC (Regulated) | | Pin 2 | Passive | Power Ground | | Pin 3 | Output | Sync control; White wire of 710P | | Pin 4 | Output | +6.

75 VDC (Regulated); Blue wire of 710P | | Pin 5 | Input | Sync control; Orange wire of 710P | | Pin 6 | Passive | Sync Ground; Green wire of 710P | | Pin 7 | Output | Shutter (A); Red wire of 710P | | Pin 8 | Output | Shutter (B); Black wire of 710P | | Pin 9 | Passive | Ground when shunt in JP2 Pins 1,2; Brown wire of 710P | | Pin 10 | Input | 7.

4 VDC (600 mA) input when shunt in JP2 Pins 3,4 | | Pin 11 | Input | Trigger Input | | Pin 12 | Passive | Signal Ground | | Pin 13 | Output | Electronic sync output |

#### Notes - P1 connections: Proper JP1 selection must be made for proper shutter operation. Please see “Jumper Selections” below. - Pins 3, 4, 5, 6: Used only when shutter is equipped with electronic sync.

- Pin 9: Used for shutter frame grounding or external low voltage input, jumper selectable. - Pin 12: Active-high or active-low output when electronic sync is activated, jumper selectable. - Pin 10: Trigger input: Minimum voltage 1. 5 VDC, maximum voltage 20 VDC, active-high only. P1 plug is removable.